How Percona XtraBackup works¶
Percona XtraBackup is based on InnoDB’s crash-recovery functionality. It copies your InnoDB data files, which results in data that is internally inconsistent; but then it performs crash recovery on the files to make them a consistent, usable database again.
This works because InnoDB maintains a redo log, also called the transaction log. This contains a record of every change to InnoDB data. When InnoDB starts, it inspects the data files and the transaction log, and performs two steps. It applies committed transaction log entries to the data files, and it performs an undo operation on any transactions that modified data but did not commit.
The --register-redo-log-consumer parameter is disabled by default. When enabled, this parameter lets Percona XtraBackup register as a redo log consumer at the start of the backup. The server does not remove a redo log that Percona XtraBackup (the consumer) has not yet copied. The consumer reads the redo log and manually advances the log sequence number (LSN). The server blocks the writes during the process. Based on the redo log consumption, the server determines when it can purge the log.
Percona XtraBackup remembers the LSN when it starts, and then copies the data files. The operation takes time, and the files may change, then LSN reflects the state of the database at different points in time. Percona XtraBackup also runs a background process that watches the transaction log files, and copies any changes. Percona XtraBackup does this continually. The transaction logs are written in a round-robin fashion, and can be reused.
Percona XtraBackup uses Backup locks
where available as a lightweight alternative to FLUSH TABLES WITH READ
LOCK. MySQL 8.4 allows
acquiring an instance level backup lock via the LOCK INSTANCE FOR BACKUP
statement.
Locking is only done for MyISAM and other non-InnoDB tables after Percona XtraBackup finishes backing up all InnoDB/XtraDB data and logs. Percona XtraBackup uses this automatically to copy non-InnoDB data to avoid blocking DML queries that modify InnoDB tables.
Important
The BACKUP_ADMIN privilege is required to query the
performance_schema_log_status for either LOCK
INSTANCE FOR BACKUP or LOCK TABLES FOR BACKUP.
xtrabackup tries to avoid backup locks and FLUSH TABLES WITH READ LOCK
when the instance contains only InnoDB tables. In this case, xtrabackup
obtains binary log coordinates from performance_schema.log_status. FLUSH
TABLES WITH READ LOCK is still required in MySQL 8.4 when xtrabackup is
started with the --slave-info. The log_status table in Percona
Server for MySQL 8.4 is extended to include the relay log coordinates, so no locks are
needed even with the --slave-info option.
When backup locks are supported by the server, xtrabackup first copies
InnoDB data, runs the LOCK TABLES FOR BACKUP and then copies the MyISAM
tables. Once this is done, the backup of the files will
begin. It will backup .frm, .MRG, .MYD, .MYI, .CSM,
.CSV, .sdi and .par files.
After that xtrabackup will use LOCK BINLOG FOR BACKUP to block all
operations that might change either binary log position or
Exec_Source_Log_Pos or Exec_Gtid_Set (i.e. source binary log coordinates
corresponding to the current SQL thread state on a replication replica) as
reported by SHOW BINARY LOG STATUS or SHOW REPLICA STATUS. xtrabackup will then finish copying
the REDO log files and fetch the binary log coordinates. After this is completed
xtrabackup will unlock the binary log and tables.
Finally, the binary log position will be printed to STDERR and xtrabackup
will exit returning 0 if all went OK.
Note that the STDERR of xtrabackup is not written in any file. You will
have to redirect it to a file, for example, xtrabackup OPTIONS 2> backupout.log.
It will also create the following files in the directory of the backup.
During the prepare phase, Percona XtraBackup performs crash recovery against
the copied data files, using the copied transaction log file. After this is
done, the database is ready to restore and use.
The backed-up MyISAM and InnoDB tables will be eventually consistent with
each other, because after the prepare (recovery) process, InnoDB’s data is
rolled forward to the point at which the backup completed, not rolled back to
the point at which it started. This point in time matches where the FLUSH
TABLES WITH READ LOCK was taken, so the MyISAM data and the prepared
InnoDB data are in sync.
The xtrabackup offers many features not mentioned in the preceding explanation. The functionality of each tool is explained in more detail further in this manual. In brief, though, the tools enable you to do operations such as streaming and incremental backups with various combinations of copying the data files, copying the log files, and applying the logs to the data.
Restoring a backup¶
To restore a backup with xtrabackup you can use the --copy-back or
--move-back options.
xtrabackup will read from the my.cnf the variables datadir,
innodb_data_home_dir, innodb_data_file_path,
innodb_log_group_home_dir and check that the directories exist.
It will copy the MyISAM tables, indexes, etc. (.MRG, .MYD,
.MYI, .CSM, .CSV, .sdi,
and par files) first, InnoDB tables and indexes next and the log files at
last. It will preserve file’s attributes when copying them, you may have to
change the files’ ownership to mysql before starting the database server, as
they will be owned by the user who created the backup.
Alternatively, the --move-back option may be used to
restore a backup. This option is similar to --copy-back
with the only difference that instead of copying files it moves them to their
target locations. As this option removes backup files, it must be used with
caution. It is useful in cases when there is not enough free disk space to hold
both data files and their backup copies.
Get expert help¶
If you need assistance, visit the community forum for comprehensive and free database knowledge, or contact our Percona Database Experts for professional support and services.